Mid-USA

Primary Cover Gasket,Outer St 1989/2006,Dyna 1991/2005 Rpls Hd 60539-94B

• Economically priced
• High quality for sure scaling
• Sold each

POWER HOUSE
iber with Silicone Bead
Primary Cover Gasket
Fits Softail 1989/2006 & Dyna 1991/2005
Replaces HD# 60539-94B

Custom Springer Rocker Studs Hardbody Wide Springers & Most Custom Wide Springers,Chrome
HARDBODY
Chrome Plated Rocker Studs (Set of 4)

Threaded diameter is 1/2"
Bearing surface 3/4"

Length of threaded part is 9/16”

Performance Alternator Rotor Use With 38 Or 45 Amp Systems Rpls Hd 29999-97B & 29981-95
V-FACTOR
Standard Black Rotor
Fits Big Twin 1997/2005 with 38-45 Amp charging system
(Imported)

Rear Axle For Custom Use 3/4" Diameter, 13.5" Long Chrome Steel

• Wide assortment for builders who are looking for a specific size
• Chrome plated 4130 cold roll steel
  
• See product image for description of lengths

V-FACTOR
Chrome Plated Axle
A Length: 13 ¹/₂", B Length: 12 ¹/₄"
3/4" Diameter
(Imported)

HARDBODY

Spring Kit for Springer Forks Use with Most Custom Springers Inc Springs, Rods, Seats & Nuts

Spark Plug Covers, Sparkies Red Lens Fits All H-D Spark Plugs W/90 Degree Boots

• Designed to show your engine's spark through colored lenses at the base of the wire

V-FACTOR
Sparkies Spark Plug Cover Pair with Red Lens
Fits all Harley-Davidson spark plugs with 90° boot
For 7mm or 8mm plug wires
Sold in pairs
(Imported)

Harley-Davidson Front Fork Tubes Flt/Flh 84/99 Stock Length Rpls Hd# 45827-84

• All fork slider tubes are centerless ground from seamless aircraft tubing in either show chrome (USA) or hard chrome (Import)
• All fork tubes are sold in pairs and include spring spacers

Hard Chrome Plated
Stock 20 7/8 Length Set fits FLT, FLTC, FLTCU, FLHT, FLHTC, FLHTCU, FLHS, FLHR 1986/1996 with or without air forks
Replaces HD# 45827-84
2 US Length Set fits LST, LSTC, LST, LSTN 1986/1999
Replaces HD# 45930-86

Air Filter Element Sportster 1988/2003 Rpls Hd# 29331-96

• Engineered for increased performance
• Washable and reusable high flow 4-layer cotton element increases air flow while offering unmatched filtration for long engine life
• Not only will these filters increase horsepower in stock engines, they are a must when performance upgrades have been done your motorcycle
• Sold each

V-FACTOR
Air ilter Element, 1 5/8 width
Fits Sportster 1988/2003
Replaces HD# 29331-96

Gas Tank Center Panel,Steel Rd Side Fat Bob Tanks W/O Gauges Plain Chrome Plated
Gas Tank Center Panels available as listed. Complete with mounting hardware.V-FACTOR
Chrome Plated Kit for use with Solid Mount at Bob Tanks when not using stock instrument panel cover
(Imported)

Springer Shock Absorber, Chrome FXSTS 1988/2006 Replaces HD# 54483-88

• High quality OE replacement springer shock absorber
• Sold Each

V-FACTOR
Chrome Plated Shock Absorber
Fits XSTS 1988/2006
Replaces HD# 54483-88

Starter Relay,Delco Remy Style Bt 67/E68,Sportster 65/73 Replaces Hd 71455-67C

• High quality Delco Remy style relay

V-FACTOR
Fits Big Twin 1967/Early 1968 & Sportster Late 1971/1974
Replaces HD# 71455-67C

Handlebar Oe Ape Hanger Style Fxdwg 1993/Later* W/Crimp & Knurled Center Rpls 56079-93

• Fits like OE handlebars
• Dimpled for wiring and has diamond knurls for security
• Designed to be used in stock applications as listed and for any custom application you desire
• Total width 33, rise to handlebar grip end 9 ¹/₂, center width to beginning of bends 6, total pullback 8
• Designed for risers on 3 ¹/₂ centers

V-FACTOR
Chrome Plated
Fits XDWG 1993/Later
Replaces HD# 56079-93
(Imported)

Debris Deflector, Stainless Fits Softail 2000/2007 Rpls Hd# 60476-00A

• Designed to help keep the road grime and debris off the oil tank, starter motor and transmission area
• These stainless steel debris reflectors replaces the OE black plastic one
• or ease of cleaning and flashy good looks, the oil tank side is semi-polished while the more focal wheel side is highly polished

HARDBODY
Stainless Steel Deflector
Fits Softail 2000/2007 & all HARDBODY Softail style rear forks
Replaces HD# 60476-00A

Flat Rear Fender 7" Wide For Wide Tire Rigid Frame & Custom Use

• Designed with strength in mind, these one-piece HARDBODY rear fenders are cold rolled from 14 gauge steel
• They measure a full 48 in circumference and can be cut to your desired length
• enders are not drilled or relieved for the chain or drive belt
• See the frame and body section for fender supports

Raw Steel 7" wide flat fender
Fits Big Twin & Sportster Rigid frames

Coil High Performance Rd 4 Ohm 12 Volt All Models 1965/1979 W/Mount Cp Rpls Hd 31609-65A
These high performance dual fire round coils produce 10% greater output capacity than stock and include a seat post type mount. The two 7mm copper core spark plug wires measure 23 long and can be cut to the desired length. The screw-on tower caps include rubber seals to keep any moisture out. V-FACTOR
Chrome Plated, 12 volt, 4 OHM
Fits Big Twin 1965/1979
Replaces HD# 31609-65A
(Imported)

Rocker Arm,Shims "010" Thick Shovelhead 66/Later Use To Set End Clearance Mfg #2253
HARDWARE
Rocker Arm Shim, .010 Thick
Fits Shovelhead all years
Package of 10

Oil Tank Dipstick W/Tempgauge Sportster 2004/Later* Rpls Hd 63023-05

• Monitor your oil temperature with this chrome dipstick/temperature gauge
• Design of this dipstick provides a grip area for easy removal

V-FACTOR
Chrome Plated Dipstick
Fits Sportster models 2004/Later
Replaces HD# 63023-05

Conical Air Filter Cover Forged Aluminum, Chrome Plated Rpls Hd 28740-10

• These forward facing, exposed filter intake kits offer performance and racing looks
• The intake elbow and mount plate are made from light weight die cast aluminum and feature a show quality finish

Not legal for sale or use in California, or on any pollution-controlled vehiclesV-FACTOR
Chrome Add-On Conical Air Filter Cover
Add this forged aluminum filter cover to either mass flow intake for a custom look
Replaces HD# 28740-10

Wheel,Bearing I.D. Reducer Stl 3/4" Axle,W/1"Id Ball Bearing 1" Id Bearing To 3/4" Id

• Reducers are designed to convert wheels with 1 I.D. sealed (ball type) bearings to a ³/₄ O.D. axle

HARDBODY
Stainless Steel Pair
(Imported)

Rocker Arm,Shims .007" Thick Shovelhead 66/Later Use To Set End Clearance Mfg #2252
HARDWARE
Rocker Arm Shim, .007 Thick
Fits Shovelhead all years
Package of 10

Brake Pads For Custom Caliper Fits Jaybrake J-Four Caliper Copper Sintered Material

• Copper sintered material for long life and quiet operation
• Economically priced
• See Additional Image for dimensions
• Sold in pairs

V-FACTOR
Copper Sintered Material Brake Pads
Fits Custom Calipers

Handlebar Brake Light Switch, Big Twin & Spt 1982/1995 Rpls Hd 71574-82 & 71590-92

• High quality original equipment style replacement handlebar switches
• See below for availability of finishes
• Meets OEM specifications
• Include OEM length wires for ease of installation

V-FACTOR
Brake Light Switch
Fits Big Twin & Sportster 1982/1995
Replaces HD# 71574-82 & 71590-92

Oil Cooler Standoff Clamps Cp Use With #89000 Oil Cooler 1-1/8" X 1-1/8" Aluminum

• Billet oil cooler has twin vertical tubes that follow the front downtubes on the frames of most models
• See below for availability of finish
• Requires standoff clamps for oil cooler

V-FACTOR
Chrome Plated Clamp Pair, 1 1/8 x 1 1/8
Required for use with 89000

Fuel & Oil Line,Clear Vinyl 5/16"Id X 9/16"Od 1/8"W 25 Ft Nylon Braid Reinforced

• ¹/₈ wall, open mesh nylon braiding has been incorporated within the clear vinyl, producing a pliable hose which will not shrink or harden
• Withstands high temperatures and pressures up to 750 PSI
• Highly resistant to fuel, oil and custom blended fuels

V-FACTOR
⁵/₁₆ I.D. x ⁹/₁₆ O.D. fuel & oil line
25 foot roll, (Imported)

Belt Dr Part Quiet Cl Friction BDL Sys Round Dog Dr Rr Pulley 7 Kevlar/Alum Disc Ercp-100
Designed to help quiet the rattle that is normally associated with open belt drives or closed belt drives with vented covers. Normally the friction plates are splined to the inner clutch hub, but the quiet clutch friction plates incorporate a round dog drive to the outer clutch basket. The friction plates are bonded to aluminum for light weight. See below for availability of plate material. Fits all Round Dog type BDL belt drives.
Clutch friction Plate Kit
Includes: 7 Kevlar® friction plates (.152 thick)